Announcement

Collapse

Flagging spam

if you see a spam post, don't reply or comment on it. Just flag it. We get those flag reports and take action. That action is pretty simple. If the post is obviously spam we delete and then check few boxes to delete all other posts by that user and ban them permanently. If the post is questionable as spam then we can suspend the user and then send them a message to work it out.
So when it doubt - Flag The Post
See more
See less

Replacement enricher ( choke ) way cheaper than oem!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Replacement enricher ( choke ) way cheaper than oem!

    I had an issue with my oem enricher set up
    first the cable end that comes from the threaded portion broke
    then the plastic retaining nut cracked/ stripped
    The oem one was 85$ online....

    So i ended up finding one on ebay

    Smoothbore Parts Choke Cable - H-D with HS-40 Carbs Mikuni 990-662-001

    it was a direct fit!
    Cost about 30$ and it had a steel section/ retaining nut instead of plastic so it should be solid
    The only differences I can tell is:

    It was a bit shorter than the oem cable which was fine with me because I already had mine mounted on a bracket I made where the fuel pump used to be (cable routed over intake manifold)

    Also it springs back into place instead of being held out which I don't really mind since I usually only need it out for about a minute

    I suppose if you needed to have it stay out for longer you could use the old clothes pin behind the knob method (how I got a bike I was buying home once with dirty carbs)

    All in all I'm pleased, no more plastic nonsense

    Hopefully this helps someone, I have been unable to find out much info about the oem carbs on my bike ( 03 road star 1600 )

  • #2
    Good find. I will be saving this info. Thanks for sharing!

    Comment


    • #3
      It takes a lot of digging to get info. Motorcycle carbs just aren't your typical over-the-counter parts, and FI is making them slowly die off. The only aftermarket money left is in flat slide carbs as tuners don't care for a CV's throttle lag...

      Comment


      • roadiemort
        roadiemort commented
        Editing a comment
        Actually a competent tuner loves the BSR40 on a R*

      • Zman
        Zman commented
        Editing a comment
        A 40 properly jetted is more than up to task on these bikes.

    • #4
      Just to update this
      I ended up fixing the issue of the cable being too short
      After i removed the stock one long with the threaded portion that goes into the carb, the spring, and the enricher plunger, I compared the two cables side by side, with the knob pushed all the way in on both
      If you attempt this make sure the tensioner on the new cable is fully tightened in, it is hidden under a rubber cover (the stock one doesn't have a cable tensioner)

      The amount of cable sticking out of the sheath (stickout) was a little shorter on the replacement cable, it could be installed as is but as mentioned before the tension will always be there on the plunger and essentially the choke will always be on, just a little

      The ideal situation on this cable or any cable that needs adapting where this half ass hack will actually work is that the cables are the same length but the new cable's sheath is too long
      I wiggled the end cap of the cable sheath loose and out of the way and using an angle grinder with a cut off wheel and my eagle eye precision I trimmed the cable sheath without nicking the cable itself
      I mainly just ground it down till it was thin enough to cut with some dikes,I'm not THAT brave (or stupid) to just cut right through it with hopes of not cutting the cable itself

      This process basically increased the cable stickout on the new cable, giving the choke cable/plunger assembly the slack it needed to function properly, even if you cut it a little too short you also have the ability to adjust the tension on it with the tensioner assembly (cover that back up with the rubber cover you removed earlier)

      With all that being said and done and reassembled on the bike the enricher knob functions as intended, it stays out when it is pulled out and has the proper amount of slack
      The added benefit of the metal locking nut/metal knob housing is well worth the time, and comparing $30 and 30 minutes of my time to a new cable costing $80 the question of was this worth it wasn't even there.

      hopefully this helps someone in the future, if it helped you go post the solution to a thread you started on here!

      Comment


      • #5
        Good to know. Thanks for sharing all the info.

        Comment

        Latest Posts

        Collapse

        Topics Statistics Last Post
        Started by thunderace4, 4 hours ago
        4 responses
        12 views
        0 likes
        Last Post Father Pobasturd  
        Started by 03LiquidSilver, 06-07-2019, 04:44 AM
        20 responses
        137 views
        0 likes
        Last Post Chromepony  
        Started by Jaybo, 2 days ago
        8 responses
        86 views
        0 likes
        Last Post Chromepony  
        Started by Leiurus, 14 hours ago
        9 responses
        79 views
        0 likes
        Last Post Chromepony  
        Started by thunderace4, 3 days ago
        6 responses
        122 views
        0 likes
        Last Post thunderace4  
        Started by jdhard0341, 4 hours ago
        2 responses
        19 views
        0 likes
        Last Post davej
        by davej
         
        Started by Leiurus, 15 hours ago
        18 responses
        82 views
        0 likes
        Last Post Jlb76
        by Jlb76
         
        Started by slack007, 1 day ago
        10 responses
        98 views
        0 likes
        Last Post Lug Nut
        by Lug Nut
         
        Started by Shores, 6 hours ago
        1 response
        31 views
        0 likes
        Last Post Lug Nut
        by Lug Nut
         
        Started by Padre, 6 hours ago
        2 responses
        26 views
        0 likes
        Last Post Bikerron  
        Started by boomerA, 1 day ago
        13 responses
        135 views
        0 likes
        Last Post davej
        by davej
         
        Started by Father Pobasturd, 05-24-2019, 02:51 PM
        659 responses
        7,766 views
        1 like
        Last Post Ahodge75  
        Started by midnitmike, 1 week ago
        13 responses
        247 views
        2 likes
        Last Post highvoltage  
        Started by Jaybo, 2 days ago
        15 responses
        158 views
        0 likes
        Last Post Shores
        by Shores
         
        Started by MikeyC, 3 days ago
        12 responses
        170 views
        0 likes
        Last Post davej
        by davej
         
        Started by Road Star Charlie, 1 day ago
        3 responses
        88 views
        0 likes
        Last Post Lug Nut
        by Lug Nut
         
        Started by Overkill jones, 1 week ago
        33 responses
        487 views
        0 likes
        Last Post Father Pobasturd  
        Started by Lamarc88, 1 day ago
        5 responses
        103 views
        0 likes
        Last Post Bikerron  
        Started by Mitch82, 2 days ago
        14 responses
        155 views
        1 like
        Last Post highvoltage  
        Started by Spydr, 1 day ago
        12 responses
        88 views
        0 likes
        Last Post cike
        by cike
         
        Working...
        X