Did you tap your new swing arm bearings in with a hammer or use a threaded rod with bolts and washers?
Announcement
Collapse
No announcement yet.
Installing new swing arm bearings.
Collapse
X
-
It's always better to press in bearings, or pull them in using threaded rod, rather than hammer them in. It's to easy to damage or misalign bearing trying to hammer it in.
I see you are cooling the bearing, if you heat the swingarm with a heat gun, sometimes you get lucky and the bearing will slide right in.
- 1 like
Comment
-
Thanks for the suggestion guys, but no amount of heating the swing arm or cooling the bearing will make it "just slide in". At least not on the 1700s. [Maybe if I had some liquid nitrogen?] I'm off to buy some threaded rod.
Comment
-
Originally posted by Doc_V View PostThanks for the suggestion guys, but no amount of heating the swing arm or cooling the bearing will make it "just slide in". At least not on the 1700s. [Maybe if I had some liquid nitrogen?] I'm off to buy some threaded rod.
FYI, I think I saw you were buying a drill press. I have an old Delta drill press with a cast iron table and a pretty hefty quill, I use that as a press. I also have a Smithy Granite that I use as a press also. You have to be careful to judge if you drill press is beefy enough, to try this. But when you use heating and cooling of components, it works pretty well most of the time, except for the most stubborn tight press fits
This isn't the Delta drill press which I used when doing RoadStar swingarm, but this is using my Smithy Granite drill press for the Honda swingarm bushings,
.
Here I pressed in some leaf spring bushings, you can see the frost on the bushing. I did 8 of these, a couple practically fell in, the other I had to pressed in. it all depends on the tolerances.
Comment
-
I definitely understand the principles of heating and cooling for bearings, I'm just saying in the case of the R* swing arm, there's no getting around needed to press them in.
It was putting the swing arm back on the bike that I hated. The damn thing is heavy and awkward; plus you have to lift up the front end first, to clear the front end of the fender, but getting it aligned to slide in the swing arm axle in was the hardest part.
Comment
-
That graphic is pretty freakin spot on. I may have to use it some time.
To be honest, I'm no glutton, just stupid enough to try. I'd much rather not have to deal with any of this crap, but thanks to a lying dumbass tow truck driver, and the dipshit who mounted my new tire before the trip, the bike has *never* been the same. Apparently, asking for a bike that doesn't become unstable above 60 mph, is a bridge too far.Last edited by Doc_V; 11-10-2020, 05:04 AM.
Comment
Latest Posts
Collapse
Topics | Statistics | Last Post | ||
---|---|---|---|---|
Started by MrG, 08-30-2020, 03:09 PM
|
14 responses
273 views
0 likes
|
Last Post
![]()
by MikeyC
1 hour ago
|
||
Started by Pauli466, 19 hours ago
|
3 responses
85 views
0 likes
|
Last Post
![]()
by EP Roadie
2 hours ago
|
||
Started by EnergyGuy, 14 hours ago
|
6 responses
70 views
2 likes
|
Last Post
![]()
by EP Roadie
2 hours ago
|
||
Started by roadiemort, 8 hours ago
|
3 responses
46 views
1 like
|
Last Post
![]()
by Brad_G
4 hours ago
|
||
Fuel relay
by 2 dogs
Started by 2 dogs, 1 day ago
|
17 responses
171 views
0 likes
|
Last Post
![]()
by 2 dogs
4 hours ago
|
||
Started by Lug Nut, 1 week ago
|
25 responses
373 views
1 like
|
Last Post
![]()
by Lug Nut
5 hours ago
|
||
Started by LDofDC, 12-23-2020, 12:17 PM
|
85 responses
463 views
0 likes
|
Last Post
![]()
by EnergyGuy
14 hours ago
|
||
Started by Hank1988, 6 days ago
|
32 responses
250 views
2 likes
|
Last Post
![]()
by Blackbeard
20 hours ago
|
||
Started by JBones, 3 days ago
|
14 responses
153 views
0 likes
|
Last Post
![]()
by EnergyGuy
21 hours ago
|
||
Started by roadiemort, 1 day ago
|
5 responses
89 views
2 likes
|
Last Post
![]()
by ItBeMe
21 hours ago
|
||
Started by brianmac, 22 hours ago
|
0 responses
33 views
0 likes
|
Last Post
![]()
by brianmac
22 hours ago
|
||
Started by matthewrosspeebles, 2 days ago
|
18 responses
186 views
0 likes
|
Last Post
![]()
by EP Roadie
1 day ago
|
||
Started by Smokescreens, 4 days ago
|
14 responses
307 views
1 like
|
Last Post
![]()
by Lifeguard
2 days ago
|
||
Started by Blackbeard, 1 week ago
|
11 responses
174 views
0 likes
|
Last Post
![]()
by davej
2 days ago
|
||
Started by EnergyGuy, 5 days ago
|
11 responses
206 views
1 like
|
Last Post
![]()
by brianmac
2 days ago
|
||
Started by roadiemort, 4 days ago
|
3 responses
108 views
0 likes
|
Last Post
![]()
by ItBeMe
2 days ago
|
||
Started by Pauli466, 4 days ago
|
3 responses
80 views
0 likes
|
Last Post
![]()
by Pauli466
3 days ago
|
||
Started by Dan58, 5 days ago
|
14 responses
138 views
0 likes
|
Last Post
![]()
by DEEPHATE
3 days ago
|
||
Started by Shores, 4 days ago
|
10 responses
117 views
0 likes
|
Last Post
![]()
by EP Roadie
3 days ago
|
||
Started by Jclevesque, 06-02-2018, 11:19 AM
|
10 responses
561 views
0 likes
|
Last Post
![]()
by brianmac
3 days ago
|
Comment