Announcement

Collapse
No announcement yet.

Looking for Engine rebuild kit

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Ace
    commented on 's reply
    And be disowned from the brotherhood!..Ace

  • Bikerron
    replied
    .....crank bearings etc.
    The crankshaft bearings are an integral part of the cases. Bearing(s) out of specs- you replace the case.

    Crank out of specs- Yep. Replace that.

    Leave a comment:


  • Horsehammerr
    replied
    Got 109,000 miles on my '01 and it never fails me.

    Leave a comment:


  • Father Pobasturd
    replied
    I understand your mindset, might as well do it while you are in there. But this ain't no H-D or short block Chevy, these bikes are built to last. Once you get a look at the cylinders you'll see they probably still look brand new. IIRC you can't get bearings for the bottom end. Usually if someone has one that's just been totally abused, they go on Ebay and find a whole motor for $500 - 800, but even that is rare. The worst thing that happens to them is you might have a lifter fail if someone ran shitty oil in it. If you have a head gasket issue it's probably because someone got in there poking around where they didn't need to be. The bikes are so cheap to buy it makes no sense to dump a bunch of money in one to fix it unless you just like throwing money away. I have a 2006 also with almost 60K miles on a stock motor, runs perfect.

    Leave a comment:


  • Jclevesque
    replied
    I would try to re-torque the head could stop oil leak. Shouldnt need to rebuild.

    Leave a comment:


  • Lug Nut
    replied
    Why donyou think you need to rebuild the motor? Why donyou think you have a gasket leak? Seems like you might be spending a lot of $ and time for no real reason.

    Leave a comment:


  • davej
    replied
    I don't think there is any such kit.You will need to make a parts list and find them thru a dealer or parts outlet.

    Also you do not have to pull the engine to get the heads off. You can even pull the cylinders and pistons without removing the engine. Also unless you have a couple hundred thousand miles on the bike there is no reason to split the case to look at the lower end. If you re-ring it do not hone the cylinders, you will destroy the coating in the cylinders if you do hone them.

    Leave a comment:


  • WTHill5
    started a topic Looking for Engine rebuild kit

    Looking for Engine rebuild kit

    Looking for a complete rebuild kit, to include piston rings head gaskets crank bearings etc. for my 2006 1700 Roadstar. Currently I am fairly certain I have a head gasket leak and while I have it apart I figure I’ll run through the entire thing and give it a little TLC while I have the engine pulled just for sake of simplification. Thanks!

Latest Posts

Collapse

Topics Statistics Last Post
Started by Motorcycler, 10 minutes ago
1 response
2 views
0 likes
Last Post roadiemort  
Started by Pauli466, 1 day ago
8 responses
95 views
0 likes
Last Post Pauli466  
Started by cike, 4 hours ago
6 responses
41 views
0 likes
Last Post Lug Nut
by Lug Nut
 
Started by bencadenbach, 1 day ago
3 responses
60 views
0 likes
Last Post Lug Nut
by Lug Nut
 
Started by Ironman, 10 hours ago
6 responses
37 views
0 likes
Last Post roadiemort  
Started by bencadenbach, 1 day ago
6 responses
74 views
0 likes
Last Post Txulrich  
Started by Kenkaman, 2 days ago
16 responses
154 views
0 likes
Last Post LeLimoMan  
Started by Vicious, 1 day ago
6 responses
67 views
0 likes
Last Post LeLimoMan  
Started by Father Pobasturd, 2 days ago
7 responses
71 views
0 likes
Last Post Ironman
by Ironman
 
Started by JoeBloShmo, 1 day ago
3 responses
54 views
0 likes
Last Post Ironman
by Ironman
 
Started by NCB, 3 weeks ago
23 responses
261 views
0 likes
Last Post NCB
by NCB
 
Started by brianmac, 1 day ago
13 responses
110 views
0 likes
Last Post Father Pobasturd  
Started by Pauli466, 1 week ago
29 responses
363 views
0 likes
Last Post DikW
by DikW
 
Started by Parhamj, 1 day ago
3 responses
44 views
0 likes
Last Post 07 silverado  
Started by thunderace4, 10-19-2019, 12:34 PM
21 responses
219 views
0 likes
Last Post bencadenbach  
Started by Parhamj, 2 days ago
2 responses
74 views
0 likes
Last Post Parhamj
by Parhamj
 
Started by GNR10, 3 days ago
3 responses
51 views
0 likes
Last Post Bikerron  
Started by Pauli466, 2 days ago
5 responses
80 views
0 likes
Last Post Pauli466  
Started by jjvw, 2 weeks ago
11 responses
310 views
0 likes
Last Post brianmac  
Started by roadiemort, 1 day ago
1 response
48 views
1 like
Last Post Chromepony  
Working...
X