front wheel spacers for hd wheels 1inch or 25mm

[Renpo6]

HI there , I'm interested just one question do thy come with a center spacer? spacer between the adapters Thanks

[Smokescreens]

no. they are 2 peices that center the wheel and adapt the axle at the same time. makes for a very simple install.

[Renpo6]

sounds good how can i order a set ?
Im in NC 28213

[Smokescreens]

i prefer paypal for payment. i will pm you so we can figure out the payment method.

[Knotty2003]

I would like to order some spacers for a 25 mm Harley bearing please

[Smokescreens]

pm replied.

[zulater1990]

I would like to purchase 1” spacers if you have some available

[Smokescreens]

i make them to order. i will send you a pm to arrange payment.

[79280z]

I would like a set of these. I am looking to put a set of HD 21in 3.5in spoke wheels onto my 2005 road star. Would i need anything else? I also am looking for fender risers for this same set up. Do i even need risers?

[Smokescreens]

you can just cut the nuts off the inside of the fender and re drill the holes in the stock fender. no kit needed. for the front you will also need to space in your calipers 9/32" and get 10mm longer bolts for the calipers.

i assume you only meant you want to run a 21" in the front?

[79280z]

Yes 21 is the front. How can i purchase your adaptors?

[Smokescreens]

i prefer paypal. if you have that you can pm me your email. also i need to know if your harley wheel will have 1 inch or 25mm bearings.

[79280z]

Great i will pm you. The wheels have 1 inch bearings

[Seanjarvis]

I’m looking for a set of 1 inch spacer for my 21 enforcer wheel to put on my 06 roadstar

[Starrider]

Put a19 inch enforcer wheel on my roadie ...11.8 rotors ..25 mm spacers...all works great...question is ..no one said anything about the spacer inside the wheel..no goons ride on center of bearring to well...something to think about or just let it ride

[Smokescreens]

Are you talking about the tube between the bearings themselves or between the ends of my adapters?

[Sasquatch]

I'm interested in purchasing a set of spacers.

[jrbk]

adapters that center a hd front wheel as well as adapt the axle to fit the 1 inch or 25mm bearings. turned from 304 stainless steel so you will never need to worry about rust or corrosion.

you only need to tell me if you want 1inch or 25mm style adapters. $75

as for your wheel you want 11.8" rotors and will need to space the calipers as needed and raise your front fender if using a 21" wheel

I just picked up a 19" enforcer with ABS bearings. Can I use it with ABS bearings or do I need to replace? Also: 1inch or 25mm - is that the ID of the hub on the enforcer (OD of the spacer that inserts into the wheel)? Thank you.

[jrbk]

Thank you Smokescreens! That is very helpful.

[jrbk]

Smokescreens, so I would need to get the 1/4" spacers for the calipers. Would I also need to get longer bolts? If so, do you know how long they should be? Thank you.

[Smokescreens]

The bolts need to be 10 mm longer. And the caliper spacers technically need to be 9/32 of a inch thick. However if you have a floating caliper you can get away with the 1/4 inch thick spacers.

[Otisluke]

Are you still making the spacers?

[Bobbin-Martin]

Hey smokescreen. Im new to this forum and was wondering if you still make spacers for HD wheels. Im trying to use some HD wheels for my 02 Midnight star bobber build, instead of spending 2k for custom wheels. Don't know if it'll help any, but I've attached a picture of the wheels I want to use. It's a 17 front and 16 rear setup. If so please PM me on how I can order some. Thanks

[Lug Nut]

Hey smokescreen. Im new to this forum and was wondering if you still make spacers for HD wheels. Im trying to use some HD wheels for my 02 Midnight star bobber build, instead of spending 2k for custom wheels. Don't know if it'll help any, but I've attached a picture of the wheels I want to use. It's a 17 front and 16 rear setup. If so please PM me on how I can order some. Thanks

Rears don't just bolt on...need a LOT of work to fit

[Benjy CCMC]

Still doing the spacers/adaptors? i need some advice, etc regards what i actually need to make it happen. looking to do a 21 inch fat spoke front. do you have a kit of with all the spacers, etc required?