Announcement

Collapse
No announcement yet.

Engine going in today

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Rob in FL
    replied
    Got the matching rotor also

    Leave a comment:


  • Rob in FL
    commented on 's reply
    Thank you! I used up part of my retirement savings on that thing

  • highvoltage
    commented on 's reply
    WOW. What a good looking wheel.

  • Rob in FL
    replied
    120/70-21 tire
    Attached Files

    Leave a comment:


  • roadiemort
    commented on 's reply
    That will look terrible, send it to me lol.

  • Rob in FL
    replied
    Look what showed up today
    Attached Files

    Leave a comment:


  • Rob in FL
    replied
    Thanks Tim

    Leave a comment:


  • TimB
    replied
    Hey Rob, You're clutch cable should be here Saturday.

    Leave a comment:


  • Rob in FL
    commented on 's reply
    Thank you ! Getting close now

  • Doc_V
    commented on 's reply
    What roadiemort said.

  • roadiemort
    commented on 's reply
    Yup, If you go single do it right so it looks factory.

  • Chromepony
    replied
    Rob in Ok...what an awesome scooter !
    You deserve an extra large piece of pie !!

    Leave a comment:


  • Doc_V
    commented on 's reply
    Tykes_Place deserves the thanks, he's the one the fixed it.

  • Rob in FL
    commented on 's reply
    Nice thanks for confirmation on the caliper

  • Rob in FL
    commented on 's reply
    I have been doing decompression treatments 3x a week I did try inversion but it hurt too bad with all the nerve damage

  • Rob in FL
    replied
    Front brake parts

    Leave a comment:


  • Rob in FL
    replied
    What the front wheel looks like

    Leave a comment:


  • Rob in FL
    replied
    My front wheel is supposed to be here next week it's a rc components majestic 21 inch with matching stainless rotor. I got a single sided rotor (left side) I have a 2011 Stryker front master cylinder I rebuilt and repainted it bought a speigler black stainless front brake line and I'm going to see if the front caliper from a yzf 750 (6 piston) is going to work. So, I cut the caliper mounting tabs off the right leg today and rough finished it with a da sander. At the top of the fork leg where the white plastic ring goes I'm going to fill that gap with fiberglass strand filler then bodywork both legs and paint them gloss black epoxy

    Leave a comment:


  • Rob in FL
    replied
    Mocked up the rear fender today it's a barons custom 2 bob if you buy one there are no holes cut you have to
    measure and cut yourself there were a couple of depression marks from the mold but they were not even close to my subframe.

    Leave a comment:


  • Rob in FL
    commented on 's reply
    Thank you !

Latest Posts

Collapse

Topics Statistics Last Post
Started by area1509, 11-12-2019, 05:31 PM
27 responses
504 views
0 likes
Last Post area1509  
Started by Herrindude, 3 weeks ago
57 responses
561 views
0 likes
Last Post Bikerron  
Started by roadiemort, 1 week ago
45 responses
109 views
0 likes
Last Post LDofDC
by LDofDC
 
Started by Lug Nut, 5 hours ago
0 responses
21 views
0 likes
Last Post Lug Nut
by Lug Nut
 
Started by Darkwingduck, 12 hours ago
3 responses
40 views
0 likes
Last Post texasscott1  
Started by Father Pobasturd, 2 weeks ago
70 responses
569 views
0 likes
Last Post Chromepony  
Started by Bricejevinn, 6 days ago
10 responses
201 views
0 likes
Last Post Duke
by Duke
 
Started by zingpow, 03-13-2019, 12:04 PM
49 responses
497 views
0 likes
Last Post brianmac  
Started by JD64k, 2 weeks ago
4 responses
176 views
0 likes
Last Post JD64k
by JD64k
 
Started by Dick M, 1 week ago
14 responses
243 views
0 likes
Last Post Shores
by Shores
 
Started by daveto, 1 day ago
5 responses
51 views
0 likes
Last Post Shores
by Shores
 
Started by roadiemort, 1 day ago
1 response
73 views
0 likes
Last Post brianmac  
Started by Bikerron, 1 day ago
0 responses
54 views
0 likes
Last Post Bikerron  
Started by Leiurus, 08-23-2019, 07:28 AM
38 responses
966 views
1 like
Last Post Leiurus
by Leiurus
 
Started by GreasySam, 10-03-2019, 06:13 AM
17 responses
284 views
0 likes
Last Post GreasySam  
Started by cike, 2 days ago
6 responses
110 views
0 likes
Last Post Kroyleahcim  
Started by cromwell, 1 week ago
16 responses
176 views
0 likes
Last Post Bikerron  
Started by Shores, 4 days ago
9 responses
226 views
0 likes
Last Post Jaybo
by Jaybo
 
Started by jdhard0341, 4 days ago
4 responses
92 views
0 likes
Last Post brianmac  
Started by rondo_calrissian, 5 days ago
4 responses
119 views
0 likes
Last Post Shores
by Shores
 
Working...
X